The Chevy Silverado is equipped with two blend door actuators. The driver side is easy to access, while the passenger side requires removal of the dashboard cover and upper dash mounting bolts.
In addition, you will have to remove the passenger airbag and the passenger vent register before you can access the driver’s side blend door actuator. Then, you can replace the actuator on both sides.
The upper blend door actuator is the part of the blend door.
It is located inside the vehicle’s dashboard. The lower is located by the heater core.
Depending on your vehicle, you may need to replace one or both.
In both cases, you will need to replace both of these parts.
If you find both parts to be defective, you can try to repair them yourself.
The cost of a new blend door actuator in your Chevy Silverado depends on where you’d like to install it. The cost will vary from $200 to $300, depending on the make and model of your vehicle.
However, the labor charges are usually the same: $ 130 or so. Depending on the type of vehicle, you may have to purchase different parts.
Where are all the blend door actuator located?
When your car’s doors blend, you should take a look inside the dash panel to see where all the blend door actuators are located.
These are generally located in the lower section of the dashboard, on either side of the power outlet.
You should be able to locate two or three screws that hold the dash panel in place.
In many cases, you can also use a flathead screwdriver to remove the safety clip holding the door in place. Make sure to be gentle with the safety clip.
The blend door actuator is a small plastic box with electronics and plastic gears in it.
This piece of technology can fit in the palm of your hand. But where is all the blend door actuator located? – Learn where to find it on your vehicle and how to replace it. Here are some tips for replacing your car’s blend door actuator: Check for broken gear teeth or a loose or broken gear.
If the blend door does not open and close properly, there’s a problem with the actuator. An obstruction can cause the blend door to malfunction and prevent it from moving.
The gears can get too worn and break, causing the blend door to remain in one position. Some common obstructions include pens, toothpicks, and small toys, bubble gum, and even the occasional sock. To avoid a problem like this, children should not place anything in the air vents.
Where is the blend door actuator located on a 2000 Chevy Silverado?
If you’re unsure where to start, read this quick guide. This component controls the blend door of the vehicle.
These parts are often easy to replace. In order to properly repair these parts, they must be completely disassembled.
Luckily, you can perform the repair yourself. First, locate the actuator.
The location will vary slightly from car to car. To remove it, use a 5.5mm socket and screwdriver to remove the screws.
Then, remove the plastic cover underneath the dashboard.
Remove the plastic cover using a small socket and ratchet. Carefully unscrew the two or three screws and carefully remove the blend door actuator.
Next, remove the blend door and any wiring that may be attached to it. Then, remove the two or three screws that mount the actuator. You may need a small universal wrench to get to the screws in awkward places.
Next, remove the IP instrumental panel. You’ll need to remove the driver side blend door. Once the blend door is removed, you can access the actuator by removing the IP instrumental panel and disconnecting the HVAC system.
Once you’re done, remove the old blend door actuator and replace it with the new one. Be sure to note all screws and bolts in the dashboard.
How do I know which blend door actuator is bad?
There are several signs that your blend door actuator may be faulty, and one of these is a clicking noise on the dashboard.
The noise will be persistent and repetitive, and will originate from the HVAC controls area. If you hear this noise, you should contact a mechanic to get a proper diagnosis. Fortunately, a replacement part is easy to find. In this article, we will explore the causes and possible solutions.
The most common cause of the sound is an obstruction. The plastic gears inside the blend door actuator can break off when there is an obstruction in their way.
This causes the door to stay closed and makes the sound worse. The obstruction can be anything, from pens and toothpicks to small toys and bubble gum. You should make sure you do not put anything into the air vents to avoid this problem.
Another common symptom is a droning or screeching sound in the dashboard. This is often most noticeable when the air-conditioning system is turned on or the temperature is raised.
This is usually the result of a problem with the plastic gear. It’s very common for plastic gears to break down due to wear. Hence, you should take your car to a technician for a diagnostic.
How do I reset my blend door actuator Silverado?
A bad blend door can be a big hassle, so it’s important to know how to reset it. It is usually located under the dash on the passenger side.
Firstly, turn on the a/c system and then turn the dial to 90 for about thirty seconds. Then, turn it back to 60. The blend door should reset itself after this. If not, check your fuses.
Next, disconnect the negative terminals on your vehicle.
Then, connect the positive terminals to the radio.
Wait for a few seconds for the capacitive charges to dissipate, then turn the ignition back on.
This procedure should clear the problem. Now, it’s time to check your blend door motor.
Make sure that it’s not stripped. Otherwise, it’s time to replace the unit.
To repair the blend door actuator, you will need to remove the panel covering the fuse box and then unscrew the two screws that hold the actuator in place.
Once you’ve removed the mounting screws, you can loosen the blend door actuator by hand. Be sure to take the screws with you so they don’t fall out while you work on the wiring connector. Finally, you’ll need to manually adjust the blended door’s speed to ensure smooth operation.