If you have a power antenna on your Toyota 4Runner, you may want to disconnect it so that you can connect the new one. The power antenna is a coaxial cable that connects your car to a satellite radio. If it is broken, it needs to be repaired or replaced. Then, you can install the new antenna. This article will show you how to do this.
Before removing the old mast, you should remember which way the plastic center cable teeth face. The antenna is fixed to the wheel well by a single bolt. The wire from the motor and transmitter connects to the antenna through the grommet in the cab. You should carefully pull the well liner back to free the old mast. Now, you can install the new one. After removing the old one, tighten the nut on the antenna.
Once you’ve removed the old antenna, make sure to clean all the grease and debris. It can be difficult to remove all of this grease and dirt, so you need to be careful when you’re doing this. The best way to clean it is to reassemble it with new parts. The fender well is the location to find a new power antenna. It might be in a bad place, so take care to find a place to install the new one.
How do I disconnect my power antenna?
How do I disconnect my power antenna? The power antenna is a vehicle accessory that uses an electrical connection to operate.
To remove it, simply turn off the car ignition and remove the connectors attached to the spool. Next, unscrew the mast and disconnect the two connectors attached to the relay. Then, remove the lock mechanism and unplug the antenna. You can now remove the antenna from the vehicle.
If the power antenna is stuck, you must disengage it first. Usually, the problem is the cable. The cable may be broken or the motor may not be functioning properly.
Before disconnecting the power antenna, you must first remove the back bumper or the rear luggage compartment trim. Then, you must remove the antenna’s coax connector and the power to the antenna. After this, you should reconnect all the components.
To do this, remove the antenna motor and disengage it from the electrical connector. Make sure that the drain hose and ground strap are disconnected.
You can also disconnect the geared cable inside the mast. You can easily repair the problem by yourself. The entire procedure will take about 2 hours and cost you about $25 for the cable/mast and a special wrench. If the problem persists, you can always purchase a replacement from a junkyard for about $75.
How do I lower the antenna on my 4Runner?
First, locate the antenna. It should be sticking out between the B-Pillar and the seat frame. Slide the antenna cable between these two pieces and slide the trim tool under the strip. Pull the cable up until it is flush with the front kick panel. Repeat this process for the other side of the vehicle. Once the antenna cable is tucked away, lower the vehicle. Now you can install the new antenna cable.
To remove the old mast, remove the dash panel bolt. Pull the dash panel out of its clip. Note the direction of the teeth on the plastic center cable. It should point toward the rear of the car. Then, pull the old mast out of its clip. Once the old mast is removed, unscrew the nut. The new mast should now stick up and be held in place with the push rod.
Next, locate the antenna cable. Then, use the pliers to remove the plastic clips that secure the antenna to the mast. They are held on by a long Phillips head bolt. Pull the upper and lower D-pillar plastic out of their clips using the tools provided. Once the antenna cable is out, the old mast will come off easily. Then, remove the old antenna, and insert the new one.
Can you replace a power antenna with a regular one?
To replace a power antenna with a regular type, remove the cover on the power unit.
Disconnect the coaxial cable and the power connector. Next, cut off the top part of the antenna.
It is made of aluminum, so it is easy to work with. The top part is usually removable, and the inside is reusable. After cutting off the top section, remove the plastic insert.
Once you remove the top mounting nut, you can unscrew the antenna. The top nut will have tiny notches that will break off with a pair of needle-nose pliers.
You can also remove it with hand tools. Before removing the antenna, tape it with a piece of tape to prevent slipping or scratching it. Afterwards, remove the motor from the vehicle.
To replace a power antenna, first disconnect the negative battery cable and then remove the radio. You should be able to access the antenna motor.
Remove the top mounting nut and rubber grommet, and unscrew the antenna motor from the car frame. After removing the motor, plug in the new motor. It should work immediately. You can also test the new antenna by connecting it to the car’s radio.